Saniflo Toilets

The Saniplus system enables the installation of an entire bathroom 15 feet below a sewer line or 150 feet away from a soil stack.

• Toilet
• Urinal
• Sink
• Shower
• Bathtub

Features and benefits:

• The Saniplus has vibration absorbers which reduces the operating sound of the pump by 10db.
• The motor for the Saniplus is sealed for life in an oil filled enclosure
• The Saniplus was designed so that moving parts are kept to an absolute minimum
• The macerator blades rotate at 3600 RPM
• The Saniplus has a normal cycle of 10-15 seconds keeping power consumption at a minimum
• The discharge elbow at the top of the Saniplus can be turned either left or right or back (depending on the discharge installation)
• A pre-installed non-return valve prevents back flow into the unit
• The Saniplus pumps the effluent upward to 15 feet and/or 150 feet horizontally (with gravity fall)
• When the water level goes down the micro switch deactivates the unit until the flush is activated again
• Installation (extremely simple installation)
• The macerator/pump is connected to the spigot of a horizontal rear discharge toilet
• The toilet tank is connected to the water supply
• The macerator/pump is connected to the small diameter discharge pipe work
• The macerator/pump is connected to the electrical supply

Important factors:

• An internal pressure chamber starts and stops the unit and the motor drives the stainless steel macerator blades and pump
• The motor is activated by a micro switch in the pressure chamber when flushed
• The impeller and macerator blades are driven by a common spindle/shaft
• The centrifugal force causes the reduced solids to be expelled through a grill into the container where it is picked up by the impeller pump mounted beneath the motor
• The wastewater from other sanitary fixtures is discharged into the Saniplus via two 2-inch inlets on either side of the housing. Either one or both inlets can be used as necessary
• When adding a bathtub or shower a base in required. This base should be made out of 2" x 6" (minimum) or 2” x 8” (recommended) to allow for the installation of a P-trap and the required 1/4”per foot gravity flow towards the pump unit.
• This unit has been designed with a vent connection on the lid. All plumbing codes require connection to a vent system. Please note that the vent system should be a two-way air vent. The use of mechanical vents, air admittance valves or similar devices are not permitted as these are considered one-way air vent systems. It is also highly recommended for the macerator/pump to be connected to a Ground Fault Interrupter (GFI) circuit.
• The Saniplus unit must be connected to a Saniflo rear discharge toilet.
  
• The Saniplus has been certified to American and Canadian Standards. Macerating standard; US: CSA Certified & IAPMO (UPC) listed - ASME A112.3.4, CA: Macerating Standard CSA B45.9.

Dimensions:  10 1/2" H x 20" W x 6 3/4" D
Amperage:   7.2
Voltage:  110
HP:  .4

System requires a rear spigot Saniflo toilet.

More Info »

Rated 5 Stars 

The Sanivite gray water pump is the perfect solution for a basement apartment or anywhere else that you need to add additional plumbing fixtures. The Sanivite is preferred for heavy duty application because of its unique design and capabilities.

The inside of the Sanivite is comprised of a pressure chamber, which starts and stops the unit, and the motor, which drives the pump.

When the water enters the Sanivite, it activates a micro switch in the pressure chamber, which in turn starts the motor. The motor is sealed for life in an oil filled enclosure. A spindle/shaft drives the impeller and therefore the moving parts are kept to an absolute minimum. Water enters the chamber and is pumped away into the sanitary sewer.

The unit pumps the effluent upward to 16 feet and/or 150 feet horizontally (with gravity fall). Once the water is discharged and the water level in the container goes down, the micro switch deactivates the unit until water enters the unit again. A normal operating cycle for the Sanivite can be as short as 2 - 10 seconds depending upon the discharge pipe run configuration; power consumption is therefore minimal.

Waste water from additional sanitary fixures is discharged into the sanivite via two 1-1/2” inlets on either side of the housing and another on top. The sanivite can accommodate a sink, shower, bathtub, urinal and even a whirlpool (additional base needed for shower and tub).

This unit has been designed with a vent connection on the lid. All plumbing codes require connection to a vent system. Please note that the vent system should be a two-way air vent. The use of mechanical vents, air admittance valves or similar devices are not permitted as these are considered one-way air vent systems.

It is also highly recommended for the gray water pump to be connected to a Ground Fault Interrupter (GFI) circuit.

The Sanivite is small enough to fit comfortably inside a kitchen cabinet or vanity or inside the overhang of a whirlpool.

• Motor RPM: 3600
• Horsepower: 0.3
• Electrical Supply:     110-115V; 60Hz;
• Flow rate at max head USG / MIN: 16 ft:18 usg/min;3 ft:29 usg
• Amperage: 4.5AMP
• Discharge Pipe Diameter: 1" diameter
• Vertical Discharge: 16 ft
• Horizontal Discharge: 150 ft
• Gravity fall on horizontal installations: 1/4" per ft
• Normal Running Time WC: 2–10 seconds
• Maximum Temperature: 140°F
• Dimensions (measured from floor level): H10-1/8" x W14-5/8" x D7¼"
• Materials: Polypropylene, C.R.P., stainless steel, Neoprene

More Info »

Rated 5 Stars 

Install a Toilet Anywhere You Want.  High Level Of Styling.

Installing a bathroom where you want is often difficult and sometimes even impossible. The main drainpipe is either too far away, or the new bathroom or sink will be lower than the drainpipe, making conventional installation unworkable.

The Sanipack is built into a wall cavity provided by a concealed frame system. The reservoir is also built into the wall and all the user sees is a large push button that activates the flush. The Sanipack is a system that is used to install a complete bathroom up to 9 feet below the sewer line, or even up to 100 feet away from a soil stack.

Since the reservoir, the macerating pump and the pipes are hidden from view, this type of installation gives you the lean and clean look of a European bathroom. The Sanipack is simplicity itself to install; there are just four connections:

• The macerating pump is connected to the discharge pipe coming from the wall hung toilet.
• The toilet tank is connected to the water supply.
• The macerating pump is connected to small diameter discharge pipe work.
• The macerating pump is connected to electrical supply.

Note: the toilet bowl and wall carrier are supplied by other manufacturers. Sanipack can be used with any North American wall-hung toilet system

Motor RPM	3600
Horsepower	0.3
Electrical Supply	110-115V; 60Hz;
Flow rate at max head USG / MIN	9 ft:22 usg/min;3 ft:26 usg
Amperage	5.4 AMP
Discharge Pipe Diameter	3/4" diameter
Vertical Discharge	9 ft
Horizontal Discharge	100 ft
Gravity fall on horizontal installations	1/4" per ft
Normal Running Time WC	10–15 seconds
Maximum Temperature	104°F
Water Consumption	1.3 US gal -WC Dependable
Dimensions (measured from floor level)	H11" x W16¾" x D4¾"
Materials	Polypropylene, C.R.P., stainless steel, Neoprene

 

More Info »

Install a Toilet Anywhere You Want.  High Level Of Styling.

Installing a bathroom where you want is often difficult and sometimes even impossible. The main drainpipe is either too far away, or the new bathroom or sink will be lower than the drainpipe, making conventional installation unworkable.

This modern shaped self-contained china toilet emulates the European wall-hung toilets that are so popular as of late. The Sanistar is a self contained toilet with the macerator pump and an electrical activated flushing action built inside the unit. The Sanistar does not depend on gravity, therefore it can be used where large diameter pipe cannot be used.

The Sanistar saves space and can be hung on any sturdy wall. It comes complete with a wall bracket system that can be placed against a wall or if you start from scratch-it can be built into the wall and mounted against 2" x 6" studs. The wall bracket has feet that can be adjusted to allow the Sanistar to be hung at a height that is comfortable for the user, for example between 15 and 18 inches.

**See photo under specs for actual toilet sold** 

 

• White Rounded Front
• Motor RPM      3600
• Horsepower     0.4
• Electrical Supply     110-115V; 60Hz;
• Flow rate at max head USG / MIN      9 ft:18 usg/min;3 ft:25 usg
• Amperage      9.0 AMP
• Discharge Pipe Diameter     1" diameter
• Vertical Discharge     9 ft
• Horizontal Discharge     100 ft
• Gravity fall on horizontal installations     1/4" per ft
• Normal Running Time WC     10–15 seconds
• Maximum Temperature     95°F
• Water Consumption     1.3 US gal
• Dimensions (measured from floor level)     H16-3/8"* x W15¾" x D20½"

More Info »

Unlike the rest of the Saniflo pump range which work on a macerator the Sanibest uses an actual grinder system. The Sanibest is meant for situations where what goes down the toilet is out of your control. It is ideal for rental units, offices, warehouse and public bathrooms. The Sanibest was created to deal with foreign sanitary articles that were flushed down the toilet.

The sanibest allows you to install a bathroom 18 feet below the sewer line or 150 feet away from the soil stack. It can handle gray water waste from a toilet, sink, bathtub, shower and even a washing machine when connected through an indirect connection.


Key features:

• Build a complete bathroom 18 feet below the sewer line or 150 feet away from a soil stack.
• Simple installation- only 4 connections to install
  • The grinder pump is connected to the spigot of a horizontal rear discharge toilet
  • The toilet tank is connected to the water supply
  • The grinder pump is connected to the small diameter discharge pipe work
  • The grinder pump is connected to the electrical supply
• 10-20 second operating cycle resulting in minimal power consumption
• Sanibest automatically adjusts the input rate from other fixtures (priority to toilet water)

The inside of the Sanibest is comprised of a pressure chamber, which starts and stops the unit, and the motor, which drives the stainless steel cutting blade and the pump. When the flush is activated, the water flowing into the Sanibest activates a micro switch in the pressure chamber, which in turn starts the motor. The motor is sealed for life in an oil filled enclosure. A common spindle/shaft drives the impeller and the blades. The moving parts therefore are kept to an absolute minimum. Water and organic waste matter, enter the chamber and are reduced to slurry as the blades rotate at 3600 RPM. The reduced solids are picked up at the bottom and the impeller mounted beneath the motor ejects the waste.

The unit pumps the effluent upward to 18 feet and/or 150 feet horizontally (with gravity fall). Once the water level in the container goes down, the micro switch deactivates. A normal operating cycle for the Sanibest takes about 7-9 seconds depending upon the discharge pipe run configuration.

Additional plumbing fixtures Sanibest supports:

• Sink
• Urinal
• Bidet
• Washer (sink or tub required)
• Shower (base required)
• Tub (base required)

The wastewater from other sanitary fixtures is discharged into the Sanibest via two 1½-inch inlets on either side of the housing. The discharge elbow on top of the Sanibest can be rotated 360 degrees depending on the discharge installation. A non-return valve (included in assembly) prevents back flow into the unit.

This incredible, unique system lets you install an entire bathroom in formerly unworkable or impractical spaces.

 

Dimensions:  12" H x 21" W x 8" D
Amperage:  9.0
Voltage:  110
HP:  .7

 

The Sanibest unit must be connected to the Saniflo rear discharge toilet. It is highly recommended for the grinder to be connected to a Ground Fault Interrupter (GFI) circuit.

More Info »

Rated 5 Stars 

The Sanigrind allows you to install a bathroom up to 18 feet below the sewer line or 150 feet away from the soil stack. Unlike any other pump in the Saniflo line the sanigrind was designed to work in conjunction with a typical bottom outlet toilet. It also differs from most other saniflow products in that it incorporates an actual grinder system as opposed the macerator the other products use. The Sanigrind can be connected to and discharge gray wastewater from a toilet, shower, sink, bathtub and washing machine. It was specifically created to deal with situations where you have no control over what goes down the toilet such as in a rental unit or office.

Benefits and features:

• Grinder unit only (works with any regular bottom outlet toilet)
• Based on the best selling Sanibest system
• The Sanigrind unit discharges the effluent through a 3/4-inch diameter pipe into a sanitary gravity drain.
• The typical operating cycle for Sanigrind is approximately 10–20 seconds, resulting in the minimum power consumption.
• Wastewater from other fixtures is released into Sanigrind via two 1½-inch inlets, on either side of the housing. Either one or both inlets can be used as required.
• The discharge elbow on top of the Sanigrind can be turned either to the left or to the right, depending on the discharge installation.
• Made for human waste and toilet tissue. It can however grind up other substances that may have unintentionally been flushed down the toilet (I.e. strands of wool, sanitary napkins, condoms, but not dental floss, cat litter or disposable diapers)

Other fixtures:
In addition to the toilet waste, Sanigrind will also discharge gray wastewater from a variety of other sanitary fixtures:

• Sink (Note: not kitchen)
• Bath
• Bidet
• Urinal
• Clothes washer (Note: washing machine must drain to a laundry sink or tub first).

The Sanigrind is intended to provide vertical pumping up to 18 feet as well as a horizontal discharge; for that reason a simple ball non-return valve is integrated. This allows you to install a complete bathroom where previously this would have been unfeasible or where significant capital equipment and structural work would have been required.

Motor RPM	3600
Horsepower	0.8
Electrical Supply	110-115V; 60Hz;
Flow rate at max head USG / MIN	18 ft: 13 usg/mi;3 ft: 24 usg
Amperage	9.0
Discharge Pipe Diameter	3/4" diameter
Vertical Discharge	18 ft
Horizontal Discharge	150 ft
Gravity fall on horizontal installations	1/4" per ft
Normal Running Time WC	10-20 seconds
Maximum Temperature	104°F
Water Consumption	1.6 US gal -Depends on Wc
Dimensions (measured from floor level)	H12" x W18" x D9"
Materials	Polypropylene, C.R.P., stainless steel, Neoprene

 

 

More Info »

Rated 5 Stars 

The Sanitop is the quietest and smallest macerator obtainable, designed to install an entire bathroom up to 12 feet below the sewer liner and even 120 feet away from the soil stack.

Uses:

• Toilet
• Sink

Features and Benefits:

• 10-15 second operating cycle- minimal power consumption
• Pre-assembled non-return valve which prevents back flow
• Vibration absorbers reduce the operation sound by 10db
• Works in conjunction with the rear discharge toilet
  
• The Sanitop has been certified to American and Canadian Standards
• Easy Installation
• The macerator/pump is connected to the spigot of a horizontal rear discharge toilet
• The toilet tank is connected to the water supply
• The macerator/pump is connected to the small diameter discharge pipe work
• The macerator/pump is connected to the electrical supply

• Motor RPM: 3600
• Horsepower: 0.3
• Electrical Supply: 115 V / 60 Hz
• Flow rate at max head USG / MIN: 12 ft :14 gal/min; 3 ft :2min
• Amperage: 5.0
• Discharge Pipe Diameter:  3⁄4"
• Vertical Discharge:  12 ft
• Horizontal Discharge: 120 ft
• Maximum Temperature: 104°F
• Water Consumption: 1.6 US gal
• Dimensions (measured from floor level): H 10 7⁄16" x W 13" x D 6 1⁄2"

More Info »

Install a Toilet Anywhere You Want.  High Level Of Styling.

Installing a bathroom where you want is often difficult and sometimes even impossible. The main drainpipe is either too far away, or the new bathroom or sink will be lower than the drainpipe, making conventional installation unworkable.

It can be used to install a half-bathroom up to 9 feet below the sewer line, or even up to 100 feet away from a soil stack. The Sanicompact can handle the effluent from a toilet and sink.

The Sanicompact is a combination of a vitreous china toilet bowl, macerator/pump  and an electrical flushing action built into one compact unit. That is why this toilet can be installed in very small places. The Sanicompact does not depend on gravity, so it can be used where a large diameter pipe cannot be used. This modern shaped self-contained china toilet is very water efficient, using just 1.1 USG (4 litres) of water per flush. It was designed with several purposes in mind:

• For situations where there is not enough space
• As a toilet that uses a minimum amount of water
• As a toilet for use with people that have physical limitations. 

The Sanicompact has no external water tank as the flushing mechanism is built-in and is totally electric. After use, one presses a pneumatic button on top of the bowl which activates a timer and a solenoid valve in order to fill and wash the sides of the bowl. The motor starts and the waste and paper are sucked inside where it is macerated and pumped away. The motor stops after approximately 10-15 seconds and the timer programs the refill of the bowl with fresh water.

The inside of the Sanicompact is comprised of a pressure switch and circuit board assembly, which starts and stops the unit, and the motor, which drives the blade and the pump. The motor is sealed for life in an oil filled enclosure. A common spindle/shaft drives the impeller and the macerator blades. The moving parts therefore are kept to an absolute minimum. Water and organic waste matter, enter the chamber and are reduced to slurry as the macerator blades rotate at 3600 RPM. The reduced solids are picked up and the impeller mounted beneath the motor ejects the waste. The unit pumps the effluent upward to 9 feet and/or 100 feet horizontally (with gravity fall).

The discharge elbow on the back of the Sanicompact can be rotated 360 degrees to fit any type of installation required. A non-return valve, which comes already assembled on the discharge elbow, prevents back flow into the unit.

 

The Sanicompact is a forced main and does not need to vented and connected to a vent stack. Other fixtures may need to be vented as per local plumbing codes. It is also highly recommended for the macerator/pump to be connected to a Ground Fault Interrupter (GFI) circuit.

 

 

Motor RPM	3600
Horsepower	0.3
Electrical Supply	110-115V; 60Hz;
Flow rate at max head USG / MIN	9 ft:21 usg/min;3 ft:16 usg
Amperage	7.2 AMP
Discharge Pipe Diameter	1" diameter
Vertical Discharge	9 ft
Horizontal Discharge	100 ft
Gravity fall on horizontal installations	1/4" per ft
Normal Running Time WC	10-15 seconds
Maximum Temperature	95°F
Water Consumption	1.3 US gal
Dimensions (measured from floor level)	H15¾" x W14½" x D18¼"
Materials	Polypropylene, C.R.P., stainless steel, Neoprene

 

More Info »

Rated 5 Stars 

Designed to meet the challenging and complex requirements of commercial and residential sewage systems the stainless steel Sanicubic Classic can handle multiple waste fixtures such as schools and commercial buildings. The pre-assembled heavy weight grinder pump is a two grinder coordination that dissolves solids into tiny pieces before passing it through a 1-1/2” discharge.

Key Features:

• Two 1-horsepower motors
• Independently operating grinders (each with a separate high-performance grinding system and rapidly rotating cutting blade which diminish solids in the wastewater from toilets, tubs and showers, sinks, washing machines, dishwashers, etc.).
• Simple installation
• Simple Operation
• Each pump can handle 50 gpm (if rate is higher the pump signals “overload” and the second pump is simultaneously activated until the situation is rectified)

Designed for:

• Apartment buildings
• Schools
• Commercial buildings
• Residential use
• Multi- Family units
• High multi-usage areas

The dual grinders inside operate alternately, taking turns managing the wastewater. This keeps it so that neither is more heavily used over time than the other. Nevertheless, if any pump ceases to function, the other pump will run full-time until the problem is removed.

Motor RPM	2800
Electrical Supply	220 - 240
Amperage	2 x 1500
Discharge Pipe Diameter	1 ½
Vertical Discharge	36 ft.
Horizontal Discharge	328 ft.
Working Temperature	104°F
Maximum Temperature	158°F
Dimensions (measured from floor level)	23¾ x 19¼ x 16½

More Info »

Rated 5 Stars 

The new Saniflo SaniAlarm warns you if the water in the macerator rises to an unusually high level.

Occasional abuse, power failures, or a build-up of limescale deposits in older units (that are not regularly descaled), can cause a surcharge of water in the unit.

SaniAlarm has a level pressure switch that triggers an alarm fixed on the top of the unit if the volume of water exceeds the maximum allowed level. The alarm emits a continuous 80 dB warning sound, until it is switched off and the problem rectified.

SaniAlarm is battery operated and can be fitted on most models* in the Saniflo range, including Sanispeed and Sanivite pumps.

• Suitable for new or existing Saniflo installations. SaniAlarm is quickly fitted onto the lid of the Saniflo unit. *Not suitable for use with Sanicom, Sanicondens, Sanicompact and Sanicubic.
• Power Supply 1 x 9v battery
• Dimensions (vertical height is measured from floor level) 82mm (H) 62mm (W) 33 mm (D)
• Technote Buzzer: 80 dB
• Mounting Hole: 10mm diameter 

More Info »

"For Trouble Free Maintenance"

In The United States about 2 out of 3 dwellings are supplied with hard or very hard water.
As with other domestic appliances limescale accumulation can affect the operational efficiency of your Saniflo unit.

• Specifically created for use with all Saniflo products
• Cleans + Disinfects
• Protect and Prolong the life of your Saniflo unit by regular descaling of moving parts and casing.
• Regular descaling and cleansing with specially formulated SANIFLO descaler
• Laboratory formulated with phosphoric acid
• Concentrated solution for optimum cleaning power
• Harmless to septic tank operation
• Security cap protection: push down and twist to open

Instructions for use:

• Disconnect the unit from the electrical supply.
• For macerators: Pour half of the contents into the toilet bowl.
• For gray water pumps: Pour half of the contents into the sink or fixture
  that is connected to the pump.
• Let the solution work for about 3 hours.
• Reconnect the unit to the electrical supply.
• Flush the toilet twice or let water into the pump for rinsing.

How often should you descale?
Hardness of water depends on where you live in the US and weather you have a water softener for your water supply.

Very hard water areas:   every month
Hard water areas:            every three months
Soft water areas:             every six months

More Info »

Install a Toilet Anywhere You Want.  Recommended for Intensive Use.

Installing a bathroom where you want is often difficult and sometimes even impossible. The main drainpipe is either too far away, or the new bathroom or sink will be lower than the drainpipe, making conventional installation unworkable.

Unlike the rest of the Saniflo pump range which work on a macerator the Sanibest uses an actual grinder system. The Sanibest is meant for situations where what goes down the toilet is out of your control. It is ideal for rental units, offices, warehouse and public bathrooms. The Sanibest was created to deal with foreign sanitary articles that were flushed down the toilet.

The sanibest allows you to install a bathroom 18 feet below the sewer line or 150 feet away from the soil stack. It can handle gray water waste from a toilet, sink, bathtub, shower and even a washing machine when connected through an indirect connection.


Key features:

• Build a complete bathroom 18 feet below the sewer line or 150 feet away from a soil stack.
• Simple installation- only 4 connections to install
  • The grinder pump is connected to the spigot of a horizontal rear discharge toilet
  • The toilet tank is connected to the water supply
  • The grinder pump is connected to the small diameter discharge pipe work
  • The grinder pump is connected to the electrical supply
• 10-20 second operating cycle resulting in minimal power consumption
• Sanibest automatically adjusts the input rate from other fixtures (priority to toilet water)

The inside of the Sanibest is comprised of a pressure chamber, which starts and stops the unit, and the motor, which drives the stainless steel cutting blade and the pump. When the flush is activated, the water flowing into the Sanibest activates a micro switch in the pressure chamber, which in turn starts the motor. The motor is sealed for life in an oil filled enclosure. A common spindle/shaft drives the impeller and the blades. The moving parts therefore are kept to an absolute minimum. Water and organic waste matter, enter the chamber and are reduced to slurry as the blades rotate at 3600 RPM. The reduced solids are picked up at the bottom and the impeller mounted beneath the motor ejects the waste.

The unit pumps the effluent upward to 18 feet and/or 150 feet horizontally (with gravity fall). Once the water level in the container goes down, the micro switch deactivates. A normal operating cycle for the Sanibest takes about 7-9 seconds depending upon the discharge pipe run configuration.

Additional plumbing fixtures Sanibest supports:

• Sink
• Urinal
• Bidet
• Washer (sink or tub required)
• Shower (base required)
• Tub (base required)

The wastewater from other sanitary fixtures is discharged into the Sanibest via two 1½-inch inlets on either side of the housing. The discharge elbow on top of the Sanibest can be rotated 360 degrees depending on the discharge installation. A non-return valve (included in assembly) prevents back flow into the unit.

This incredible, unique system lets you install an entire bathroom in formerly unworkable or impractical spaces.

 

This Sanibest set includes the grinder pump and Saniflo rear spigot toilet

 

Two toilet styles are available. Please select style from the options:

• Vitreous china tank and bowl with round front
• 16-3/4 inches (seating height)
• 26-1/2 inches (overall depth)

 

• Vitreous china tank and elongated bowl
• 16-3/4 inches (seating height) ADA Compliant
• 28-1/2 inches (overall depth)

 

• Toilet Features:
• Insulated tank
• Lever handle plastic, white
• Toilet tank/bowl screws comes with washers and wing nuts
• 1 year Warranty on china
• Optional Extension pipe available for remote mounting of pump
• Free Toilet Seat included with purchase

 

Dimensions: Pump Only 12" H x 21" W x 8" D
Amperage: 9.0
Voltage: 110
HP: .7

 

**See photo under specs for actual toilet sold**

 

More Info »

Rated 5 Stars 

Install a Toilet Anywhere You Want.  High Level Of Styling.

Installing a bathroom where you want is often difficult and sometimes even impossible. The main drainpipe is either too far away, or the new bathroom or sink will be lower than the drainpipe, making conventional installation unworkable.

 

The Saniplus is a system used to install a complete bathroom up to 15 feet below the sewer line, or even up to 150 feet away from a soil stack. It can handle the effluent from a toilet, sink, bathtub and shower.

The Saniplus is simplicity itself to install; there are just four connections.

• The macerator/pump is connected to the spigot of a horizontal rear discharge toilet
• The toilet tank is connected to the water supply
• The macerator/pump is connected to the small diameter discharge pipe work
• The macerator/pump is connected to the electrical supply

The inside of the Saniplus is comprised of a pressure chamber, which starts and stops the unit, and the motor, which drives the stainless steel macerator blades and the pump.

When the flush is activated, the water flowing into the Saniplus activates a micro switch in the pressure chamber, which in turn starts the motor. The motor is sealed for life in an oil filled enclosure. A common spindle/shaft drives the impeller and the macerator blades. The moving parts therefore are kept to an absolute minimum. Water and organic waste matter enter the chamber and are reduced to slurry as the macerator blades rotate at 3600 RPM. The centrifugal force causes the reduced solids to be ejected through a grill into the container where it is picked up by the impeller pump mounted beneath the motor.

The unit pumps the effluent upward to 15 feet and/or 150 feet horizontally (with gravity fall). Once the water level in the container goes down, the micro switch deactivates the unit until the flush is activated again. A normal operating cycle for Saniplus takes about 7-9 seconds depending upon the discharge pipe run configuration; power consumption is therefore minimal.

In addition to the toilet waste, the Saniplus will also discharge gray water from a variety of other sanitary fixtures such as: a sink, a bathtub, a shower and a urinal. When adding a bathtub or shower, a base will have to be constructed. This base should be made out of a 2" x 6" (minimum) or 2” x 8” (recommended) on edge, to allow for the installation of a P-trap and the required 1/4”per foot gravity flow towards the pump unit.

The wastewater from other sanitary fixtures is discharged into the Saniplus via two 2-inch inlets on either side of the housing. Either one or both inlets can be used as required. The discharge elbow on top of the Saniplus can be turned either to the left, to the right, or towards the back, depending on the discharge installation. A non-return valve, which comes already assembled on the discharge elbow, prevents back flow into the unit.

This unit has been designed with a vent connection on the lid. All plumbing codes require connection to a vent system. Please note that the vent system should be a two-way air vent. The use of mechanical vents, air admittance valves or similar devices are not permitted as these are considered one-way air vent systems. It is also highly recommended for the macerator/pump to be connected to a Ground Fault Interrupter (GFI) circuit.

The design of this model consists of vibration absorbers which enable the reduction of operating sound by reducing the transmitted sounds from any location where such resonance transmission could occur. This new design reduces the operating sound of this pump by 10dB.

 

This Saniplus set includes the macerator pump and  Saniflo rear spigot toilet

 

Two toilet styles are available. Please select style from the options:

• Vitreous china tank and bowl with round front
• 16-3/4 inches (seating height)
• 26-1/2 inches (overall depth)

 

• Vitreous china tank and elongated bowl
• 16-3/4 inches (seating height) ADA Compliant
• 28-1/2 inches (overall depth)

 

• Toilet Features:
• Insulated tank
• Lever handle plastic, white
• Toilet tank/bowl screws comes with washers and wing nuts
• 1 year Warranty on china
• Optional Extension pipe available for remote mounting of pump
• Free Toilet Seat included with purchase

**See photo under specs for actual toilet sold** 

Dimensions:  Pump only-12" H x 21" W x 9" D
Voltage: 110
HP:  .4
Amperage: 4.5

More Info »

Rated 5 Stars 

Install a Toilet Anywhere You Want.  High Level Of Styling.

Installing a HALF bathroom where you want is often difficult and sometimes even impossible. The main drainpipe is either too far away, or the new bathroom or sink will be lower than the drainpipe, making conventional installation unworkable.

The Sanitop is a system that is used to install a complete bathroom up to 12 feet below the sewer line, or even up to 120 feet away from a soil stack. It can handle the effluent from a toilet and sink.

A normal operating cycle for Sanitop takes about 7-9 seconds depending upon the discharge pipe run configuration; power consumption is therefore minimal.

A non-return valve, which comes already assembled on the discharge elbow, prevents back flow into the unit.

The design of this model consists of vibration absorbers which enable the reduction of operating sound by reducing the transmitted sounds from any location where such resonance transmission could occur. This new design reduces the operating sound of this pump by 10dB.

The Sanitop is simplicity itself to install; there are just four connections.
- The macerator/pump is connected to the spigot of a horizontal rear discharge toilet.
- The toilet tank is connected to the water supply.
- The macerator/pump is connected to the small diameter discharge pipe work.
- The macerator/pump is connected to the electrical supply.

The Sanitop has been certified to American and Canadian Standards.

 

This Sanitop system includes the Sanitop macerator pump and Saniflo rear spigot toilet

Two toilet styles are available. Please select style from the options:

• Vitreous china tank and bowl with round front
• 16-3/4 inches (seating height)
• 26-1/2 inches (overall depth)
•  Vitreous china tank and elongated bowl
• 16-3/4 inches (seating height) ADA Compliant
• 28-1/2 inches (overall depth) 
• Toilet Features:
• Insulated tank
• Lever handle plastic, white
• Toilet tank/bowl screws comes with washers and wing nuts
• 1 year Warranty on china
• Free Toilet Seat included with purchase
  
• Optional Extension pipe available for remote mounting of pump

 

**See photo under specs for actual toilet sold**

Motor RPM 3600
Horsepower 0.3
Electrical Supply 115 V / 60 Hz
Amperage 5.0
Discharge Pipe Diameter 3⁄4"
Vertical Discharge 12 ft
Horizontal Discharge 120 ft
Maximum Temperature 104°F
Dimensions (measured from floor level) H 10 7⁄16" x W 13" x D 6 1⁄2"

More Info »

Rated 5 Stars 

The Sanishower is a gray water pump small enough to fit inside a vanity cabinet or a raised shower base. The Sanishower pumps waste water from a shower, sink, bar sink and other fixtures. It is capable of pumping water 12 feet in height or 100 feet away from the soil stack. The Sanishower makes it possible to have a full bathroom where you never before thought possible.

As a point of interest; quite a few pedicure manufacturers are putting the Sanishower inside pedicure chairs, due to its quiet operation and ease of installation, they have become the choice of OEM's.

The inside of the Sanishower is comprised of a pressure chamber, which starts and stops the unit, and the motor, which drives the pump.

 

When the water enters the Sanishower, it activates a micro switch in the pressure chamber, which in turn starts the motor. The motor is sealed for life in an oil filled enclosure. A spindle/shaft drives the impeller and therefore the moving parts are kept to an absolute minimum. Water enters the chamber and is pumped away into the sanitary sewer.

 

The unit pumps the effluent upward to 12 feet and/or 100 feet horizontally (with gravity fall). Once the water is discharged and the water level in the container goes down, the micro switch deactivates the unit until water enters the unit again. A normal operating cycle for the Sanishower can be as short as 2 - 10 seconds depending upon the discharge pipe run configuration; power consumption is therefore minimal.

 

In addition to sinks, the Sanishower will also accept and discharge the waste water from a variety of other sanitary fixtures such as: a shower, a urinal, etc.

 

The discharge elbow on the side of the Sanishower can be rotated 360 degrees to fit any type of installation required. A non-return valve, which comes already assembled on the discharge elbow, prevents back flow into the unit.

• Motor RPM: 3600
• Horsepower: 0.2
• Electrical Supply: 110-115V; 60Hz;
• Flow rate at max head USG / MIN: 12 ft:14 usg/min;3 ft:26 usg
• Amperage: 3.5 AMP
• Discharge Pipe Diameter: 3/4" diameter
• Vertical Discharge: 12 ft
• Horizontal Discharge: 100 ft
• Gravity fall on horizontal installations: 1/4" per ft
• Normal Running Time WC: 10–15 seconds
• Maximum Temperature: 104°F
• Dimensions (measured from floor level): H5¾" x W11-5/8" x D6-3/8"
• Materials: Polypropylene, C.R.P., stainless steel, Neoprene
  

More Info »

Rated 5 Stars 

The easy fix to complicated problems…The Saniswift is a modern design gray water which can be used anywhere in a home. The Saniswift allows you to add plumbing fixtures such as kitchen, laundry or bar sinks, dishwasher and even a washing machine through an indirect connection. The Saniswift offers opportunities you never dreamed were possible.


The Saniswift is a gray water pump that is ideally suitable for use in a
basement apartment or anywhere in the house where additional fixtures
are most wanted. It will pump the waste water away from a variety of
sources such as: a kitchen sink, laundry sink, washing machine
(indirect connection), dishwasher, bar sink, etc.

The Saniswift's modern style prevails over other bulky relics. This
system offers powerful and economical pumping action in a compact,
contemporary design. With unprecedented performance and features,
this pump is unmatched in its class.

The inside of the Saniswift comprises of a pressure switch and circuit
board assembly, which starts and stops the unit, and the motor, which
drives the pump.

When the water enters the Saniswift, it activates a pressure switch
which in turn starts the motor. The motor is sealed for life in an oil filled
enclosure. A spindle/shaft drives the impeller and therefore the moving
parts are kept to an absolute minimum.

The unit pumps the effluent upward to 14 feet and/or 140 feet horizontally (with gravity fall). Once the water is discharged and the water level in the container goes down, the pressure switch deactivates the unit until water enters the unit again. A normal operating cycle for the Saniswift can be as short as 2 - 10 seconds depending upon the discharge pipe run configuration; power consumption is therefore minimal.

In addition to a sink, the Saniswift will also accept and discharge the waste water from a variety of other sanitary fixtures such as: a kitchen sink, a shower, a urinal. When adding a shower, a base will have to be constructed.
This base should be made out of a 2" x 6" (minimum) or 2” x 8” (recommended) on edge, to allow for the installation of a P-trap and the required 1/4” per foot gravity flow towards the pump unit.

The waste water from other sanitary fixtures is discharged into the Saniswift via two 1-1/2 inch inlets, on either side of the housing and an additional inlet on the top of the unit. A non-return valve, which comes already assembled on the discharge rubber connector, prevents back flow into the unit.

This unit has been designed with a vent connection on the lid. All plumbing codes require connection to a vent system. Please note that the vent system should be a two-way air vent.

It is also highly recommended for the gray water pump to be connected to a Ground Fault Interrupter (GFI) circuit.

The Saniswift is a compact unit with attractive rounded contours that fits neatly into tight spaces.

• Motor:     Induction Motor
• Motor RPM:     3600
• Horsepower:     0.3
• Electrical Supply:    110-115V; 60Hz
• Flow rate at max head USG / MIN:      14 ft:18gal/min;3ft: 24gal/min
• Amperage:      5.9
• Discharge Pipe Diameter:     1" diameter
• Vertical Discharge:     14 ft
• Horizontal Discharge:     140 ft
• Gravity fall on horizontal installations:    1/4" per ft
• Normal Running Time WC:     2-10 seconds
• Maximum Temperature:     140°F
• Dimensions (measured from floor level):    H8-3/4" x W9" x D101/4"
• Materials:     Polypropylene, C.R.P., stainless steel, Neoprene

More Info »

Rated 4 Stars